Where to find product information
Where to find product information
This guide includes the basic safety guidelines in the printed Safety & Warranty booklet that comes with your Pixel 8a. It also includes additional safety, regulatory, and warranty information about Pixel 8a.
Safety and regulatory information: g.co/pixel/safety or Settings 
Warranty details for your country of purchase, including instructions for making a claim: g.co/pixel/warranty.
Electronic regulatory labels (and specific absorption rate (SAR) values) for your device: Settings
Eco-design (energy performance) information: g.co/ecodesign.
Comprehensive online help: g.co/pixel/help.
Safety warnings
 |
WARNING: HEALTH AND SAFETY INFORMATION; READ BEFORE USE TO REDUCE THE RISK OF PERSONAL INJURY, DISCOMFORT, PROPERTY DAMAGE, INCLUDING DAMAGE TO YOUR DEVICE, ACCESSORIES OR ANY CONNECTED DEVICES, AND OTHER POTENTIAL HAZARDS. |
Handling
Handle your phone with care. You may damage the device or the battery if you disassemble, drop, bend, burn, crush or puncture your device. Do not use a phone with a damaged enclosure, a cracked screen or some other form of physical damage. Using a damaged phone may cause overheating or injury. Do not expose your phone to liquids, which can cause a short circuit and overheating. If your phone gets wet, do not attempt to dry it using an external heat source.
Your phone works best in ambient temperatures between 32° and 95° F (0° and 35° C), and should be stored between ambient temperatures of -4° and 113° F (-20° and 45° C). Do not expose your phone to temperatures above 113° F (45° C), such as on a car dashboard or near a heating vent, as this may damage the phone, overheat the battery, or pose a risk of fire. Keep your phone away from heat sources and out of direct sunlight. If your device becomes too hot, disconnect it from its power source if it is plugged in, move it to a cooler place and do not use it until it has cooled. Your phone is designed to work best at an altitude of up to 16404 ft (5000m).
Use of your phone in certain modes, such as gaming, taking videos, using a flashlight setting, or virtual reality or augmented reality features, can cause it to generate more heat than it would under normal operating conditions. This may cause your phone to operate in a reduced-power mode or temporarily shut down. Use extra care when operating the device in these modes. For more information on risks associated with prolonged heat exposure, please refer to the Prolonged Heat Exposure section below.
Repair & service
Self service repair is not recommended unless you are an adult with the technical expertise to safely repair electronic devices. If you choose to perform self repair, you agree to assume the risk associated with such repair. Use caution if engaging in repair. Opening and/or repairing your device can present electric shock, device damage, fire and personal injury risks and other hazards. Disassembling the device may result in loss of water or dust resistance or cause injury or damage to your device. For example, the device contains a laser that can be damaged during disassembly which might expose you to hazardous laser emissions which are not visible.
Contact customer service if phone is not working properly or has been damaged. For more information, visit g.co/pixelcare.
Charging
Be sure the power adapter and phone are well ventilated when in use or charging. Using damaged cables, or power adapters, or charging when moisture is present, can cause fire, electric shock, injury, or damage to the phone or other property. Do not charge your phone when it’s wet. Avoid charging your device in direct sunlight.
When charging the device, make sure the power adapter is plugged into a power outlet near the device and is easily accessible. Do not force this power adapter and other plugs or power adapters to a power outlet if space is not sufficient to accommodate both. When disconnecting the power adapter from a power outlet, pull on the adapter, never on the charging cable. Do not twist or pinch the cable, and do not force a connector into a port. If you receive a message while charging that instructs you to unplug the charging device, disconnect the charging device or power adapter. Before attempting to charge again, make sure both the charging cable connector and the device's charging port are dry and clear of any objects.
Only charge your phone with the included cable or compatible charging accessories available on the Google Store or at Google authorized resellers (look for Google’s “made for” badge). The AC adapter must be certified with a Limited Power Source output per IEC 60950-1 and/or classified PS2 per IEC 62368-1, rated: 5 Volts DC, maximum 3 Amp; 9 Volts DC, maximum 3 Amp; or both and qualified per CTIA Certification Requirements for Battery System Compliance to IEEE 1725. Failure to use compatible charging accessories can cause fire, electric shock, injury, or damage to the device and the accessories.
Wireless charging
Your phone may be charged with a Qi-compliant or Google approved wireless charger. Do not place other metallic or magnetic objects between the wireless charger and your phone, as this could cause heating of the other object or cause your device not to charge properly. Examples of such objects include coins, jewelry, SIM tray tools and credit cards. If using a phone case that is metallic or magnetic, remove the case prior to wireless charging as this may cause the device or charger to overheat or cause the device not to charge properly.
Prolonged heat exposure
The phone and its charger generate heat during normal operation and comply with applicable surface temperature standards and limits. Avoid prolonged skin contact when the device is in use or charging because exposing skin to hot surfaces for a long period of time may cause discomfort or burns. Do not sleep on or with your device or its power adapter, or cover them with a blanket or pillow. Be aware of this issue if you have a physical condition that affects your ability to detect heat against your skin.
Child safety
This device is not a toy. Your phone may contain (or may come with) small parts, plastic, cables, glass, or metal elements, and parts with sharp edges that may cause an injury or create a choking or strangulation hazard. Children have strangled on cords and cables. Keep the phone and its accessories, including cords and cables, out of the reach of children (more than 3 feet (0.9 meters) away) and do not allow them to play with the phone and its accessories. They could hurt themselves or others, or could accidentally damage the phone. Seek medical attention immediately if small parts are swallowed or injury occurs.
Hearing loss
 |
Prolonged exposure to loud sounds (including music) can cause hearing loss. To prevent possible hearing damage, avoid listening at high volume for prolonged periods of time. Continued exposure to high volumes and background noise can make loud sounds seem quieter than they actually are. Check the volume before using headphones or earphones. |
Battery
This phone contains a lithium-ion battery, which is a sensitive component that can cause injury if damaged. Google recommends that you seek professional assistance for any device repairs. Self service repair (including removing and/or replacing the battery) is not recommended unless you are an adult with technical expertise to safely repair electronic devices. If you choose to perform self repair, you agree to assume the risk associated with such repair. Use caution if engaging in repair. Opening and/or repairing your device can present electric shock, device damage, fire and personal injury risks, and other hazards. We recommend that you contact Google or a Google authorized service provider to replace the battery. For contact information, visit g.co/pixel/contact. Use of a non-qualified battery may present a risk of fire, explosion, leakage, or other hazard. Do not modify or remanufacture/refurbish the battery, puncture or attempt to insert objects into the battery, immerse or expose the battery to water or other liquids, or expose the battery to fire, excessive heat, and/or other hazards.
This device comes with a battery that has proper certifications. In addition, the battery complies with IEEE 1725 standard.
Disposal, transportation & recycling
Dispose of and transport your device, batteries and accessories according to local environmental and transportation regulations. Do not improperly transport them or dispose of them in normal household waste. Improper disposal or transport may lead to fire, explosion, and/or other hazards. Do not open, crush, heat above 113° F (45° C), or incinerate. For more information on recycling your device, batteries and accessories, visit g.co/HWRecyclingProgram.
Environmental restrictions
To prevent damage to your device parts or internal circuits, do not use or store the device or its accessories in dusty, smoky, damp, or dirty environments, or near magnetic fields. Keep it away from heat sources and out of direct sunlight. Do not leave your device inside a vehicle or in places where the temperature may exceed 113° F (45° C), such as on a car dashboard, window sill, near a heating vent, or behind glass that is exposed to direct sunlight or strong ultraviolet light for extended periods of time. This may damage the device, overheat the battery, or pose a risk of fire or explosion.
Explosive atmospheres
Do not charge, use, store, or transport your device where flammables or explosives are stored (e.g., in gas stations, fuel depots, or chemical plants). Do not use your device where blasting operations are in progress, or in potentially explosive atmospheres such as fueling areas, fuel storehouses, below deck on boats, fuel, or chemical transfer or storage areas, and in areas where the air contains chemicals, vapors, or particles (such as grain, dust, or metal powders). Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Observe all notices and signs where these hazards might exist. Do not leave your device inside a vehicle or in places where the temperature may exceed 113° F (45° C), such as on a car dashboard, window sill, near a heating vent or behind glass that is exposed to direct sunlight or strong ultraviolet light for extended periods of time. This may damage the product, overheat the battery or pose a risk of fire or explosion.
Navigation
Your device can access mapping and navigation services. Maps and navigation depend on a working data connection and location services, and may not be available at all times or in all areas. Maps and directions may be inaccurate and actual conditions may differ from the map, data, traffic, directions, content and other results. Carefully review directions, follow all applicable traffic laws and signs, exercise your independent judgment and apply common sense, and use mapping and navigation services at your own risk. You are responsible at all times for your conduct and its consequences. Navigation with AR requires up to date Google Street View imagery and bright outdoor light, and isn’t available in India.
Distraction
Using your device when performing certain activities can distract you and may cause a dangerous situation for you or others. To reduce the risk of accidents (and because it’s prohibited by law in many places), do not use your device while driving, bicycling, or while operating machinery, and do not use it while engaging in any activities that have potentially serious consequences. Follow local laws about using mobile devices, headphones, and helmets.
Radio frequency exposure
This device has been evaluated and meets the applicable regulatory requirements for exposure to radio waves and is designed and manufactured not to exceed the applicable emission limits for exposure to radio frequency (RF) energy.
In the countries where the Specific Absorption Rate (SAR) limit is 1.6 W/kg averaged over one gram of tissue,the highest SAR values for this device type are 1.11 W/kg for Pixel 8a (G8HHN) and 1.10 W/kg for Pixel 8a (GKV4X) when used against head with no separation and 0.99 W/kg for Pixel 8a (G8HHN) and 0.99 W/kg for Pixel 8a (GKV4X) against body with 1.0 cm (0.4 in) separation. In the countries where the Specific Absorption Rate (SAR) limit is 2.0 W/kg averaged over ten grams of tissue, the highest SAR values for this device type are 1.00 W/kg when used against head with no separation and 1.12 W/kg against body with 5 mm (0.2 in) separation.
You can find the SAR values applicable to each of those jurisdictions on your device: Settings
To reduce exposure to RF energy, use a hands-free option, such as the built-in speakerphone, headphones, or other similar accessories. Ensure that the device accessories, such as a device case and device holster, are not composed of metal components. Keep the device away from your body to meet the distance requirement.
You can find additional information about SAR at the following pages:
fcc.gov
icnirp.org
ec.europa.eu
dot.gov.in
Radio frequency interference
Observe rules that prohibit the use of wireless technology (e.g. cellular or Wi-Fi). Your device is designed to comply with regulations governing radio frequency emissions but use of wireless devices can negatively affect other electronic equipment. For example, while flying in an aircraft or immediately before boarding, use your wireless device only according to instructions provided by the airline. Use of a wireless device in an aircraft may disrupt wireless networks, present a hazard to aircraft operation, or be illegal. You may be able to use your device in airplane mode.
Emergency communications
Wireless devices may not be reliable for emergency communications. This device operates using radio signals and cannot guarantee that it will establish or maintain a connection in all conditions. Your device is also powered by a rechargeable battery that may be affected by temperature, use, damage, and other conditions. Never rely solely on any wireless phone for emergency communications. While some jurisdictions transmit emergency information over wireless networks, your device may not always receive these communications depending upon network connectivity or other factors. Access to some features and emergency information or communications may not be available in all areas or languages. When the phone’s screen is locked, you can initiate an emergency call with a long press on the power button and the volume up button at the same time. The screen will then show the emergency call button. Press this button to make the emergency call.
Medical device interference
Your device uses radios and other components that emit electromagnetic fields, and also contains magnets. These electromagnetic fields and magnets may interfere with medical devices, such as pacemakers and other implanted medical devices. Always keep the phone and its charger at a safe distance away from the medical device. If you have questions about using your Google device with or near your medical device, consult your healthcare provider before using your phone. If you suspect your phone is interfering with your medical device, turn off your Google device and consult your physician for information specific to your medical device.
Hospitals
Switch off your wireless device when requested to do so in hospitals, clinics or health care facilities. These requests are designed to prevent possible interference with sensitive medical equipment.
Health-related functions
Your phone and any general wellness, sleep, exercise, heart rate, and associated fitness applications or functions are not medical devices, unless otherwise clearly marked, and are intended for information purposes only. They are not designed or intended for use in the diagnosis of disease or other conditions, or in the cure, monitoring, mitigation, treatment, or prevention of disease or other conditions.
LED
The LEDs visible on your device are safe under reasonably foreseeable conditions per the requirements in IEC 62471. However, it is recommended that you do not direct the LEDs at anyone’s eyes.
Skin irritation
Some people may experience reactions to materials, such as nickel, found in items that are in extended contact with the skin. Stop use of the phone and consult a physician if you experience skin irritation in locations in frequent contact with the phone.
Medical conditions
A small percentage of users may experience headaches, seizures, blackouts, eye strain, fatigue or dry eyes that are triggered by visual stimuli, such as flashing lights or bright patterns, or use of electronics with displays. Those symptoms can be experienced by people who have never previously experienced such issues. If you have a history of seizures, blackouts, epilepsy, a medical condition, or experience discomfort that you believe could be affected by your phone, consult with a doctor before using your device. Stop using your phone immediately and contact a doctor if you experience any symptoms that you believe could be caused or affected by your phone (for example, headaches, blackouts, or seizures).
Musculoskeletal disorders
Repetitive activities, such as typing, tapping, or swiping on the screen of your phone, may cause discomfort in your fingers, hands, wrists, arms, shoulders, or other parts of your body. If you experience any discomfort from such activities, stop using your phone and consult with your doctor.
Consumer laser product
| Caution – Your phone contains a Class 1 laser module. The design of the device incorporates optics and protective housing such that there is no access to a level of laser radiation above Class 1. |
Laser modules in this product comply with EN 50689:2021, EN 60825-1+A11:2021, 21 CFR 1040.10 and 1040.11, except for conformance with IEC 60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This product should be serviced by Google or an authorized service provider.
Proximity Laser Module: Made in Austria. ams AG, Tobelbader Str. 30, 8141 Oberpremstätten, Austria
Proper handling & usage
Follow these guidelines when using, storing or cleaning of your phone.
Operating temperature
Do not use or charge the phone at ambient temperatures lower than 0°C (32°F) or higher than 35°C (95°F). If the interior temperature of the device exceeds normal operating temperatures, you may experience the following behaviors while the device tries to regulate its temperature: reduced performance and connectivity, inability to charge, or powering down of the display or device power down. You may not be able to use the device while it regulates its temperature. Move the device to a cooler (or warmer) location and wait a few minutes before attempting to use it again.
Care & cleaning
Unplug the phone and power adapter before cleaning, during lightning storms, or when unused for extended periods of time. Do not clean your phone while it is charging as this may cause injury or damage to your device. Avoid solvent and abrasive material that may cause damage to the product surface. Do not use any chemical detergent, powder, or other chemical agents (such as benzene) to clean the phone or accessories.
Exposure to makeup, chemicals, and dyed materials such as denim can stain light-colored Pixel 8a and cases.
To clean your phone we recommend gently wiping it with a soft, lint-free cloth. Use a dry cloth for streaks, smudges or dust and a slightly damp (not wet) cloth for color transfers such as from makeup or a new pair of jeans. For stains and grime, use screen wipes or eyeglass cleaner on the screen and ordinary household soap or bleach free cleaning wipes on the back and sides. For additional care and cleaning instructions, check g.co/pixel/care.
To disinfect your phone, including your screen, you can use ordinary household disinfecting wipes or 70% isopropyl alcohol-based wipes. Do not use wipes that have bleach.
Dust & water resistance
Your device is designed to comply with dust and water protection rating IP67 under IEC standard 60529 when it leaves the factory, but it is not dust proof or water proof. Dust and water resistance are not permanent conditions and are diminished or lost over time due to normal wear and tear, device repair, disassembly, or damage. Dropping your device may result in loss of dust or water resistance. Liquid damage voids the warranty. Do not expose your phone to liquids or to dust, which can cause short circuit and/or overheating. The device charger and other accessories are not dust or water resistant and should not be exposed to either. For more information, visit g.co/pixel/water.
Magnetic fields
Avoid placing any items containing magnets or which are sensitive to magnetism, such as credit cards, bank cards, audio/video tapes, or magnetic memory devices, near this phone or its charging cable connector, because you may lose information stored on such items. Items containing information sensitive to magnets should be kept at least 2 inches (5 cm) away from this phone.
Service & support
Repairs or modifications made without sufficient technical expertise could result in permanent damage to the device or injury. Google recommends that you seek professional assistance for any device repairs. Contact customer service for alternative repair service options.
If you send your device in for service, you might receive a replacement in place of your original device. Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods. If the goods are capable of retaining user-generated data then the repair or replacement may result in loss of the data. For online help and support, visit g.co/pixel/help.
Regulatory information
Regulatory information, certification, and compliance marks specific to Pixel 8a can be found on your phone under Settings
EMC compliance statement
Important: This device and in-box accessories have demonstrated Electromagnetic Compatibility (EMC) compliance under conditions that included the use of compliant peripheral devices and shielded cables between system components. It is important that you use compliant peripheral devices and shielded cables between system components to reduce the possibility of causing interference to radios, televisions, and other electronic devices.
Regulatory information: United States
FCC regulatory compliance
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Google could void your authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 2 conditions:
1. These devices may not cause harmful interference.
2. These devices must accept any interference received, including interference that may cause undesired operation.
Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.
Model number: G8HHN, GKV4X
Product name: Pixel 8a
US Responsible Party:
Google LLC
1600 Amphitheatre Parkway
Mountain View, CA 94043
Contact: g.co/pixel/contact.
Hearing Aid Compatibility (HAC)
This phone is hearing aid compatible as determined by ANSI C63.19-2019, amended under the conditions of FCC limited waiver DA 23-914. The ANSI C63.19-2019 standard does not use the rating system that older versions of the standard used, i.e. M rating, which is a measure of immunity to radio frequency interference for acoustic coupling hearing aids and T rating, which is a measure of performance when used with an inductive coupling (telecoil) hearing aid. Specifically, the 2019 ANSI Standard requires that handsets meet volume control specifications in order to be considered hearing aid-compatible under that standard. Under the waiver, certain Volume Control test requirements are relaxed or waived and certain test configurations were partially or not tested. For instance, only Commercial Mobile Radio Services (CMRS) narrowband and CMRS wideband voice codecs are required to comply with the volume control requirements of the Volume Control Standard. All other codecs, such as full-band and super-wideband codecs or over-the-top (OTT) codecs, are not required to comply with the Volume Control Standard. In order to pass the volume control requirement, a handset must meet a two-part test. The first part of the requirement tests for conversational gain with a hearing aid, and the second part of the requirement tests for conversational gain without a hearing aid. To pass both parts of the requirement, a handset must have at least 6 dB of conversational gain with or without a hearing aid.
This phone has been evaluated and meets the volume control requirements per technical specification ANSI C63.19-2019 and under FCC limited waiver DA 23-914 The actual conversational gain for fully tested Enhanced Voice Services (EVS) narrowband and EVS wideband codecs and air interface combinations is 18 dB for Pixel 8a (G8HHN) and 17 dB for Pixel 8a (GKV4X) with hearing aids and 19 dB for Pixel 8a (G8HHN) and 19 dB for Pixel 8a (GKV4X) without hearing aids. The lowest conversational gain for partially tested Enhanced Full Rate (EFR), Adaptive Multi-Rate (AMR) narrowband, and AMR wideband codecs and air interface combinations is 17 dB for Pixel 8a (G8HHN) and 17 dB for Pixel 8a (GKV4X) with hearing aids and 18 dB for Pixel 8a (G8HHN) and 19 dB for Pixel 8a (GKV4X) without hearing aids.
This phone has been tested and certified for use with hearing aids for some of the wireless technologies that they use. However, there may be some newer wireless technologies used in these phones that have not been tested yet for use with hearing aids. It is important to try the different features of your phone thoroughly and in different locations, using your hearing aid or cochlear implant, to determine if you hear any interfering noise. Consult your service provider or Google for information on hearing aid compatibility. If you have questions about return or exchange policies, consult your service provider or phone retailer.
The table below shows the wireless technologies (including frequencies/bands by air interface and codec) that were tested or not tested according to FCC rules and limited waiver DA 23-914.
|
Air interface |
Bands |
Codec |
RFE |
T-coil |
Volume control |
|
LTE/ NR/ Wi-Fi |
LTE: 2 /4 / 5 / 7 / 12 / 13 / 14 / 17 / 25 / 26 / 30 / 38 / 41 / 48 / 66 / 71 NR: n2 / 5 / 7 / 12** / 25** / 26** / 30** / 38** / 41** / 48 / 66 / 70** / 71 / 77 / Wi-Fi: 2.4 GHz, U-NII 1 / 2A / 2C / 3 / 4 / 5* |
AMR-NB, AMR-WB, EVS-NB, EVS-WB |
Yes |
Yes |
Yes |
|
EVS-SWB, OPUS |
Yes |
Yes |
No |
||
|
NR/ Wi-Fi |
NR: 260*** / 261*** Wi-Fi: U-NII 5* / 6 / 7 / 8 |
AMR-NB, AMR-WB, EVS-NB, EVS-WB, EVS-SWB, OPUS |
No |
No |
No |
|
UMTS/ GSM |
UMTS: V, IV, II |
EFR (GSM only), AMR-NB, AMR-WB |
Yes |
Yes |
Yes |
|
UMTS: V, IV, II |
OPUS |
Yes |
Yes |
No |
* U-NII 5 is tested for Hearing Aid Compatibility for channels which are entirely below 6 GHz. Channels partially or entirely above 6 GHz are not subject to testing.
** Supported on GKV4X only.
*** Supported on G8HHN only.
Regulatory information: Canada
Industry Canada, Class B
This device complies with ICES-003 Class B limits.
Your device complies with ISED license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISDE Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
The device for operation in the 5925–7125 MHz band shall not be used for control of or communications with unmanned aircraft systems
Les dispositifs fonctionnant dans la bande de 5 925 à 7 125 MHz ne doivent pas être utilisés pour commander des systèmes d’aéronef sans pilote ni pour communiquer avec de tels systèmes.
Regulatory information: UK
UK compliance notice
|
Hereby, Google LLC declares that radio equipment type: G6GPR is in compliance with Radio Equipment Regulation 2017. The full declaration of conformity may be found at g.co/pixel/conformity. |
The device is restricted to indoor use only when operating in the 5250 to 5350 MHz and the 5925 to 6425 MHz (LPI) frequency ranges in the UK.
UK PSTI statement of compliance
Information on frequency bands & wireless output power
United Kingdom
Data given here is the maximum radio-frequency power transmitted in the frequency band(s) in which the radio equipment operates.
|
Frequency |
Power |
|---|---|
|
Wi-Fi 2400-2483,5 MHz |
< 20 dBm |
|
Wi-Fi 5150-5350 MHz |
< 23 dBm |
|
Wi-Fi 5470-5725 MHz |
< 23 dBm |
|
Wi-Fi 5725-5875 MHz |
< 14 dBm |
|
Wi-Fi 5925-6425 MHz |
< 14 dBm / <23 dBm |
|
Bluetooth: 2400-2483,5 MHz |
< 20 dBm |
|
NFC 13.56 MHz |
< -9 dBuA/m @ 10m |
|
GSM 900 |
< PC 4 |
|
GSM 1800 |
< PC 1 |
|
UMTS Band I/VIII |
< PC 3 |
|
LTE B1, B3, B7, B8, B20, B28, B38, B40, B42 |
< PC 3 |
|
LTE B38 HPUE |
< PC 2 |
|
NR n1, n3, n7, n8, n20, n28, n38, n40, n41, n77, n78 |
< PC 3 |
|
NR n77 HPUE, n78 HPUE |
< PC 2 |
Radio frequency interference
Google is not responsible for any radio or television interference caused by unauthorized modification of these devices or accessories, or by the substitution or attachment of connecting cables and equipment other than that specified by Google. The correction of interference caused by such unauthorized modification, substitution or attachment is the responsibility of the user. Google and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from the user failing to comply with these guidelines.
RoHS compliance
This product is in compliance with Statutory Instrument 2012 No. 3032 The Restriction of the Use of Certain Hazardous Substance in Electrical and Electronic Equipment Regulations.
UK REACH
UK REACH (Registration, Evaluation, Authorization and Restriction of Chemicals, Statutory Instrument 2020 No. 1577) is the UK chemical substances regulatory framework. Google complies with all requirements of the regulation and we are committed to providing our customers with information about the presence of REACH Substances of Very High Concern (SVHCs). For information, you can contact Google at [email protected].
Waste Electrical & Electronic Equipment (WEEE) & Batteries
 |
The WEEE symbol at left means that according to local laws and regulations your product and its battery(ies) should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities for safe disposal or recycling. The separate collection and recycling of your product, its electrical accessories, and its battery(ies) will help conserve natural resources, protect human health, and help the environment. |
Manufacturer: Google LLC 1600 Amphitheatre Parkway, Mountain View, CA 94043, United States.
Google Commerce Limited UK establishment, Belgrave House, 76 Buckingham Palace Road, London, SW1W 9TQ.
Regulatory information: EU
EU compliance notice
 |
Hereby, Google LLC declares that radio equipment type: G6GPR is in compliance with Directive 2014/53/EU (Radio Equipment Directive). The full declaration of conformity may be found at g.co/pixel/conformity. |
Restrictions or requirements under Directive 2014/53/EU
The device is restricted to indoor use only when operating in the 5250 to 5350 MHz and 5925 to 6425 MHz (LPI) frequency ranges in AT, BE, BG, CY, CZ, DE, DK, EE, EL, ES, FI, FR, HR, HU, IE, IT, LT, LU, LV, MT, NL, PL, PT, RO, SE, SI, SK, UK (NI), CH, IS, LI, NO, TR.
Information on frequency bands & wireless output power
European Union
Data given here is the maximum radio-frequency power transmitted in the frequency band(s) in which the radio equipment operates.
|
Frequency |
Power |
|---|---|
|
Wi-Fi 2400-2483,5 MHz |
< 20 dBm |
|
Wi-Fi 5150-5350 MHz |
< 23 dBm |
|
Wi-Fi 5470-5725 MHz |
< 23 dBm |
|
Wi-Fi 5725-5875 MHz |
< 14 dBm |
|
Wi-Fi 5925-6425 MHz |
< 14 dBm / <23 dBm |
|
Bluetooth: 2400-2483,5 MHz |
< 20 dBm |
|
NFC 13.56 MHz |
< -9 dBuA/m @ 10m |
|
GSM 900 |
< PC 4 |
|
GSM 1800 |
< PC 1 |
|
UMTS Band I/VIII |
< PC 3 |
|
LTE B1, B3, B7, B8, B20, B28, B38, B40, B42 |
< PC 3 |
|
LTE B38 HPUE |
< PC 2 |
|
NR n1, n3, n7, n8, n20, n28, n38, n40, n41, n77, n78 |
< PC 3 |
|
NR n77 HPUE, n78 HPUE |
< PC 2 |
Radio frequency interference
Google is not responsible for any radio or television interference caused by unauthorized modification of these devices or accessories, or by the substitution or attachment of connecting cables and equipment other than that specified by Google. The correction of interference caused by such unauthorized modification, substitution or attachment is the responsibility of the user. Google and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from the user failing to comply with these guidelines.
Common charger directive
The power delivered by the charger must be between min 7.5 Watts required by the radio equipment, and max 27 Watts in order to achieve the maximum charging speed.
The device supports the USB Power Delivery charging protocol “USB PD fast charging."
Waste Electrical & Electronic Equipment (WEEE) & Batteries
|
The WEEE symbol at left means that according to local laws and regulations your product and its battery(ies) should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities for safe disposal or recycling. The separate collection and recycling of your product, its electrical accessories, and its battery(ies) will help conserve natural resources, protect human health, and help the environment. |
RoHS compliance
This product is in compliance with Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011, on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) and its amendments.
REACH
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals, EC No 1907/2006) is the EU chemical substances regulatory framework. Google complies with all requirements of the regulation and we are committed to providing our customers with information about the presence of REACH Substances of Very High Concern (SVHCs). For information, you can contact Google at [email protected].
Manufacturer: Google LLC 1600 Amphitheatre Parkway, Mountain View, CA 94043 United States.
Google Commerce Limited, 70 Sir John Rogerson’s Quay, Dublin 2, D02 R296, Ireland.
Regulatory information: Australia
The device is restricted to indoor use only when operating in the 5250 to 5350 MHz and 5925 to 6425 MHz (LPI) frequency ranges to reduce the potential for harmful interference to co-channel mobile satellite systems.
Regulatory information: Singapore
|
Complies with IMDA Standards DA107248 |
Regulatory information: Japan
5 GHz (W52、W53)および 6 GHz (LPI)周波数帯の場合、デバイスの使用は屋内のみに制限されます (5.2 GHz帯高出力データ通信システムの基地局や中継局との通信を除く）。
This is a Class B equipment. Although this equipment is intended for use in a residential environment, it could cause poor reception if used near a radio or a television receiver. Please follow instructions in the instruction manual.
VCCI-B
Regulatory information: India
Specific Absorption Rate (SAR) information
Your phone is a radio transmitter and receiver. It complies with the international guidelines in relation to the limiting of human exposure to electromagnetic fields, and has been specifically designed to meet the guidelines for exposure to radio waves established by the Department of Telecommunications, Ministry of Communications and Information Technology, Government of India (""DoT""). The guidelines use a unit of measurement known as Specific Absorption Rate (""SAR"") which is a unit of body-absorbed radio frequency quantity when the phone is in use. The SAR limit in India for mobile devices is 1.6 W/kg over a mass of 1 gram of human tissue.
This phone complies with these guidelines when used against head with no separation and body with 10 mm separation. Ensure that device accessories, such as device case and device holster, are not composed of metal components. Keep the device away from your body to meet the distance requirement.
For Pixel 8a, the highest Specific Absorption Rate (SAR) values reported are:
- Head: 1.11 W/kg.
- Body: 1.00 W/kg.
You can also see SAR values on the website of the DoT/ Telecommunication Engineering Centre.
While most of the laboratory studies have been unable to find a direct link between exposure to radio frequency radiation and health, the DoT has prescribed the following precautionary measures while using the mobile handset:
- Use a wireless hands-free system (headphone, headset) with a lower power Bluetooth emitter.
- Make sure the cell phone has a low SAR. Keep your calls short or send a text message (SMS) instead. This advice applies especially to children, adolescents, and pregnant women.
- Use cell phone when the signal quality is good. People having active medical implants should preferably keep the cell phone at least 15 cm away from the implant.
India recycling, e-waste management & handling statement
 |
In India, this label indicates that this product should not be thrown away with household commercial and industrial waste. It should be deposited at an appropriate facility to allow recovery and recycling. |
Google declares that your device has been designed and manufactured in compliance with E-Waste (Management) Rules, 2022 (hereafter "the Rules"), and is specifically in compliance with Rule 16 (1) on the reduction in the use of hazardous substances in the manufacture of electrical and electronic equipment and their maximum allowed concentrations by weight in the homogenous materials (except for the exemptions listed in schedule II).
Improper handling, disposal, accidental breakage, damage or improper recycling of e-waste may present risks, including, but not limited to, fire, explosion and/or other hazards, and uncontrolled waste disposal which may be detrimental to/have adverse effects on the environment as it prevents reuse of resources. Some e-waste may contain hazardous chemicals which, if disposed improperly, may make water, soil and other natural resources toxic. Improper disposal may cause harm to plant, animal and human life.
Regulatory information: Taiwan
無線射頻暴露
以G6GPR而言, SAR 標準值: 2.0 W/kg, 送測產品實測值為: 0.85 W/kg.
台灣法規遵循
使用過度恐傷害視力
(1). 使用30分鐘請休息10分鐘。
(2). 未滿2歲幼兒不看螢幕，2歲以上每天看螢幕不要超過1小時。
減少電磁波影響，請妥適使用
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
應避免影響附近雷達系統之操作。
經過格式化的實際儲存空間容量會略減。
如要查看製造年份，請在手機上依序輕觸「設定」應用程式
Taiwan RoHS
|
Equipment Name: Pixel 8a Mobile Phone, Type designation: G6GPR 設備名稱：移動電話，型號（型式）：G6GPR |
||||||
|
Unit |
限用物質及其化學符號 Restricted substances and its chemical symbols |
|||||
|
鉛Lead (Pb) |
汞Mercury (Hg) |
鎘Cadmium (Cd) |
六價鉻Hexavalent chromium (Cr+6) |
多溴聯苯Polybrominated biphenyls (PBB) |
多溴二苯醚Polybrominated diphenyl ethers (PBDE) |
|
|
外殼 Enclosure |
O |
O |
O |
O |
O |
O |
|
電子元件 Electronic Component |
－ |
O |
O |
O |
O |
O |
|
連接器 Connector |
－ |
O |
O |
O |
O |
O |
|
印刷電路板 PCB |
O |
O |
O |
O |
O |
O |
|
顯示屏 Display |
O |
O |
O |
O |
O |
O |
|
電池 Battery |
－ |
O |
O |
O |
O |
O |
|
包裝 Packaging |
O |
O |
O |
O |
O |
O |
|
其它 Other |
O |
O |
O |
O |
O |
O |
|
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準值。 Note 1: "Exceeding 0.1 wt%" and "exceeding 0.01 wt %" indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. 備考2.〝O〞係指該項限用物質之百分比含量未超出百分比含量基準值。 Note 2: "O" indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. 備考3.〝－〞係指該項限用物質為排除項目。 Note 3: The "-" indicates that the restricted substance corresponds to the exemption. |
||||||
Accessibility information
Pixel 8a|
Accessibility feature |
Requirements - description |
Value |
|
Handset/Hardware information |
||
|
Touch screen |
Does the device have a touch screen |
Yes |
|
If the device has a touchscreen, is it capacitive (sometimes referred to as heat activated) |
Yes |
|
|
Key identification |
Are individual keys easily discernible to the user |
N/A |
|
How are the keys discernible - separate keys, use of ridges to define |
N/A |
|
|
Key center point distance |
What is the distance from the center point of one number key to another |
N/A |
|
Keyboard layout |
The keypad is laid out like a QWERTY typewriter keyboard |
Yes |
|
Lanyard pin for key ring or lanyard strap |
Has a small bar allowing a key ring or neck strap (lanyard) to be attached |
No |
|
Differentiation of function keys |
The number keys have a different color or shape from the other keys, making them easier to tell apart by touch or by sight |
N/A |
|
Shape of device |
A. Clam Shell / Flip Phone B. Candy Bar / Stick C. Slide D. Swivel E. Touchscreen F. Other |
E |
|
Operating system |
The operating system and version used by this phone |
Android 14 |
|
Anti-slip features |
Has a non-slip coating or ridges to prevent it slipping out of your hand |
No |
|
Mobility/Dexterity features |
||
|
Handset weight |
Handset weight including battery |
188 grams |
|
Easy Battery Placement |
Is battery clearly marked for proper orientation and placement |
N/A |
|
Speaker-phone capable |
Hands free operation during dialing and after call initiated |
Yes |
|
Guarded/recessed keys |
Individual keys are recessed or guarded in some way to reduce the chance that you will press the wrong key |
N/A |
|
Wireless earphones/headsets |
Wireless earphones and headsets, such as Bluetooth headsets, are supported |
Yes |
|
Coupling to a device |
To allow people to use computers as text terminals. Also allows customized devices to work with the phone. Device can be connected to the phone by using: |
|
|
cable (an electrical wire) |
Yes |
|
|
infrared signal (which travels through the air like a radio wave but cannot pass through walls or other solid objects) |
No |
|
|
Bluetooth/wireless LAN (radio signals which travel through the air and may also be able to pass through walls or other solid objects) |
Yes |
|
|
other connections than those described above (please describe): NFC, UWB |
Yes |
|
|
Flat back for table top operation |
Has a flat back, so it can be used while it is lying on a table |
Yes |
|
Any key answering |
The user can answer the call by pressing any key |
No |
|
Hand movement |
Some controls require you to pinch or twist them with your fingers, or rotate your wrist |
No |
|
Voice recognition for dialing |
Allows you to dial a number by speaking the person's name, if it is stored in your contact list (a personal "telephone book" you create in your phone) |
Yes |
|
Voice recognition for accessing features |
Allows you to activate features by speaking commands into the phone, reducing the need to use the keypad |
Yes |
|
Automatic answering |
Enables the phone to pick up a call automatically after a designated number of rings |
No |
|
Vision features |
||
|
Tactile key markers – "F" and "J" |
The "F" and "J" keys have raised dots or bumps on them so you can distinguish them by touch (only relevant for phones that have a QWERTY typewriter-style keypad) |
N/A |
|
Standard number key layouts |
The number keys are laid out in the standard way with 1 2 3 at the top and * 0 # at the bottom |
Yes – touchscreen keyboard |
|
Key feedback - tactile |
When you press a key you can feel a physical click, so you know it has been pressed |
Yes |
|
Key feedback - audible |
When you press a key it makes a sound, so you know it has been pressed |
Yes |
|
Audible identification of keys - spoken |
When you press a number key the number is spoken out, so you know you have pressed the correct one |
Yes, when using TalkBack |
|
Audible identification of keys - functions |
The sounds you hear when you press a key are different for number keys and function keys, so you can easily tell them apart |
Yes |
|
Adjustable font - style |
You can change the font (typeface) used for the text on the display, which may make it easier to read |
No |
|
Adjustable font - size |
You can make the text on the display larger or smaller to make it easier to read |
Yes |
|
Personalized shortcuts |
You can assign a particular feature to a single key or a short key sequence |
Yes |
|
Display characteristics - Adjustable Contrast Control |
You can adjust the contrast of the display to make text and symbols easier to see against the background |
Yes |
|
Display characteristics - Adjustable Brightness Control |
You can adjust the brightness of the display to make it easier to read |
Yes |
|
Display characteristics - Main Display Size |
Size of the main display |
6.134" (20:9 aspect ratio) |
|
Display characteristics - Main Display Resolution |
The number of dots (called pixels) used to display text and images on the main display. More dots mean more detail. |
1080 x 2400 |
|
Display characteristics - Color Differentiation |
The information presented on the display does not rely on color perception for understanding (e.g. you do not have to be able to distinguish red symbols from green symbols) |
Yes |
|
Display characteristics - Symbols/Icons |
Menus can be displayed using symbols or pictures in a grid layout. This can make them easier for some people to understand or remember |
No |
|
Display characteristics - Screen Flicker |
The main display does not flicker at a rate that could cause problems for people with photo-epilepsy (between 2 Hz and 60 Hz) |
Yes |
|
Voice output of caller ID from contacts list |
When you receive a call, it speaks the caller's name if it is stored in your contact |
No |
|
Voice output of SMS: inbuilt |
Can read text messages out loud to you |
Yes |
|
Voiced menus |
Speaks the menu options, allowing you to access functions even if you cannot read the display |
Yes |
|
Alternative format user manual |
The user manual is available in alternative formats such as accessible online |
Yes |
|
Hearing Features |
||
|
Vibrating alert |
The phone can be set to vibrate when it receives a call or text message or when it gives a warning alert |
Yes |
|
Visual alerts - Incoming calls |
When a call or text message comes in, it displays a visual alert, such as the caller's name or photo if it is stored in your contact list |
Yes |
|
Two-way video communications – using mobile networks |
Allows you to make video calls in which you can see the other person and they can see you using your mobile network |
Yes |
|
Two-way video communications – using wireless LAN networks |
Allows you to make video calls in which you can see the other person and they can see you using your wireless LAN network |
Yes |
|
Headset – plug type |
The type of plug a headset will need to have so that it can be connected to the phone |
USB-C |
|
Hearing aid compatibility |
When used with a hearing aid set to the "T" position, the sound is clearer |
Yes |
|
Alternative hearing aid technologies |
When used with alternative coupling technologies, the sound is clearer |
N/A |
|
Messaging Options - MMS |
Allows you to send and receive multimedia messages, which can include photographs, audio and video clips |
Yes |
|
SMS personalization and reuse |
Allows you to create standard text messages that you can quickly send to anyone without having to retype them each time. For example, "I'm in a meeting; I'll call you back" |
Yes |
|
Messaging options - Email |
Allows you to send and receive email messages |
Yes |
|
Internet capability |
You can use the phone to browse websites and use other internet-based services |
Yes |
|
Additional features & Characteristics |
Google Pixel 8a is a Touch screen device. However it has the following touch keys : Power and volume control keys |
Yes |
|
Optional features & Accessories |
The nature of the open operating system and accessibility features mean that some features are provided as part of the Android operating system and as such are subject to change and upgrade during the life of the product |
Yes |
Limited warranty
The limited warranty is available in the Google Hardware Warranty Center.
©2024 Google LLC. All rights reserved.
Pixel 8a, G logo, Google, Android, and related marks and logos are trademarks of Google LLC. Wi-Fi® and the Wi-Fi logo are trademarks of Wi-Fi Alliance. The Bluetooth® word and logos are registered trademarks owned by Bluetooth SIG, Inc. Qi is a registered trademark of Wireless Power Consortium Inc. All other trademarks are the property of their respective owners.