Where to find product information
Where to find product information
This guide includes the same basic safety guidelines that are in the printed Safety & Warranty booklet inside the box of your Stadia Controller. It also includes additional safety, regulatory and warranty information about your Stadia Controller.
- Warranty details for your country of purchase, including instructions for making a claim: g.co/stadia/warranty
- Stadia Controller help: g.co/stadia/help
Safety warnings
To avoid damaging your device, accessories or any connected devices, and to reduce the risk of personal injury, discomfort, property damage or other potential hazards, follow the precautions below before using your Stadia Controller.
Handling
Handle your Stadia Controller with care. Do not drop, throw or slam it. You may damage your Stadia Controller or its
battery if you disassemble, drop, bend, burn, crush or puncture your Stadia Controller. Using a damaged Stadia
Controller may cause battery overheating or injury. Do not expose your Stadia Controller to liquids, which can cause a short circuit and overheating. If your Stadia Controller gets wet, do not attempt to dry it using an external heat source.
Your Stadia Controller should be used and charged in ambient temperatures between 0° and 35°C (32° and 95°F) and should be stored between ambient temperatures of -20° and 60°C (-4° and 140°F). Do not leave your Stadia Controller in places where the temperatures may exceed 60°C (140°F), such as in a car or near a heating vent, as this may damage your Stadia Controller, overheat its battery or pose a potential risk of fire. Keep your Stadia Controller away from heat sources and out of direct sunlight. If your device becomes too hot, disconnect it from its power source if it's plugged in, move it to a cooler place and do not use the unit until it has cooled down. Your Stadia Controller is designed to work at an altitude of up to 2,000 m (6,560 ft).
Repair & service
Do not attempt to repair your Stadia Controller yourself. Disassembling the device may cause injury to you.
Unauthorised repairs or modifications could result in permanent damage to the device and may affect your warranty coverage and regulatory authorisations.
Contact customer service and do not use your Stadia Controller if it isn’t working properly or has been damaged. For online help and support, visit g.co/stadia/help. To reach an expert, visit g.co/nest/contact.
Charging
Make sure that your Stadia Controller and its power adaptor are well ventilated when in use or charging. Using a damaged cable, power adaptor or charging when moisture is present can cause fire, electric shock, injury or damage to your Stadia Controller or other property. When charging the Stadia Controller, make sure that the power adaptor is plugged into a socket near the Stadia Controller and is easily accessible. Avoid charging the device in direct sunlight. This product is intended for use with a certified Limited Power Source (LPS) per IEC 60950-1 and/or classified PS1 per IEC 62368-1, output rated: 5 Volts DC, maximum 1.5 Amp.
Only charge your Stadia Controller with the included power adaptor and cable or compatible charging accessories. Failure to use compatible charging accessories can cause fire, electric shock, injury or damage to the device and the accessories.
When disconnecting the power adaptor from a power socket, pull on the adaptor, never the cable. Do not twist or pinch the USB cable, and do not force a connector into a port.
Prolonged heat exposure
The Stadia Controller and its charger generate heat during normal operation and comply with applicable surface temperature standards and limits. If the device gets abnormally hot or uncomfortable to touch, discontinue use, unplug it and let it cool. Exposing skin to hot surfaces for a long period of time may cause discomfort or burns. Be aware of this issue if you have a physical condition that affects your ability to detect heat against your skin.
Do not sleep on your device or its power adaptor, or cover them with a blanket or pillow.
Your device may generate additional heat when charging or using certain features, such as when powering external devices like wired headsets. Use extra care when operating the device in these modes.
Hearing loss
Prolonged exposure to loud sounds (including music) can cause hearing loss. To prevent possible hearing damage, avoid listening at high volume for prolonged periods of time. Continued exposure to high volumes and background noise can make loud sounds seem quieter than they actually are. Check the volume before using headphones or earphones.
Battery
This Stadia Controller contains a rechargeable lithium-ion battery which is a sensitive component that can cause injury if damaged. Do not attempt to remove the battery. Contact Google or a Google authorised service provider to have the battery replaced. Replacement by unqualified professionals can damage your device. Improper replacement or use of an unqualified battery may present a risk of fire, explosion, leakage or other hazard. Do not modify or remanufacture/refurbish the battery, puncture or attempt to insert objects into the battery, immerse or expose the battery to water or other liquids or expose the battery to fire, excessive heat and/or other hazards. Do not short circuit the battery or allow metallic or conductive objects to contact the battery terminals. Avoid dropping the Stadia Controller or battery. If the Stadia Controller or battery is dropped, especially on a hard surface, and you suspect or observe damage, contact Google or a Google authorised service provider for inspection. If the battery leaks, do not allow the leaking fluid to come into contact with eyes, skin or clothing. If the fluid is already in contact with the eyes, do not rub them. Rinse the eyes with clean water immediately and seek medical advice.
Dispose of your Stadia Controller, battery and accessories in accordance with local regulations. Do not dispose of them in normal household waste. Improper disposal may lead to fire, explosion and/or other hazards. Do not open, crush, heat above 60 ̊C (140 ̊F) or incinerate. For more information on recycling your Stadia Controller, visit g.co/HWRecyclingProgram
Environmental restrictions
To prevent damage to the Stadia Controller’s parts or internal circuits, do not use or store the device or its accessories in dusty, smoky, damp or dirty environments, or near magnetic fields. Keep it away from heat sources and out of direct sunlight. Do not leave your Stadia Controller inside a vehicle or in places where the temperature may exceed 60°C (140° F), such as on a car dashboard, window sill, near a heating vent or behind glass that is exposed to direct sunlight or strong ultraviolet light for extended periods of time. This may damage the Stadia Controller, overheat the battery or pose a risk of fire or explosion.
Explosive atmospheres
Do not charge, use, store or transport your Stadia Controller where flammables or explosives are stored (for example, in petrol stations, fuel depots or chemical plants). Do not use your Stadia Controller where blasting operations are in progress, or in potentially explosive atmospheres such as in areas where the air contains high levels of flammable chemicals, vapours or particles (such as grain, dust or metal powders). Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Observe all notices and signs where these hazards might exist.
Radio frequency interference
Observe rules that prohibit the use of wireless technology (e.g. Bluetooth or Wi-Fi). Your Stadia Controller is designed to comply with regulations governing radio frequency emissions, but use of wireless devices can negatively affect other electronic equipment. For example, while flying in an aircraft or immediately before boarding, use your Stadia Controller only according to instructions provided by the airline. Use of a wireless device in an aircraft may disrupt wireless networks, present a hazard to aircraft operation or be illegal.
Medical device interference
Your Stadia Controller uses radios and other components that emit electromagnetic fields, and also contains magnets inside the product. Headsets and headphones used with the device may also contain magnets. These electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the device and its charger at a safe distance away from the pacemaker or other implanted medical device. If you have questions about using your Stadia Controller with or near your pacemaker or other implanted medical device, consult your health care provider before using it. If you suspect your Stadia Controller is interfering with your pacemaker or other implanted medical devices, turn off your Stadia Controller and consult your doctor for information specific to your medical device.
Hospitals
Switch off your Stadia Controller when requested to do so in hospitals, clinics or health care
facilities. These requests are designed to prevent possible wireless interference with sensitive medical equipment.
Child safety
This device is not a toy. Your Stadia Controller may contain (or may come with) small parts or plastic elements that may create a choking hazard. The charging cable may be a strangulation hazard for small children. Keep any charging cords and cables out of reach of small children (more than 1 metre/3 feet away) and do not allow them to play with it. They could hurt themselves or others, or could accidentally damage the Stadia Controller. Consult a doctor immediately if small parts are swallowed.
Safe environment
Always be aware of your surroundings when using your Stadia Controller. Take care to ensure that you are not near other people, pets, objects or other items that you can bump into, trip over or knock down when using your Stadia Controller.
Repetitive stress injury
Repetitive movements using the device can lead to occasional discomfort in your hands, wrists, arms, shoulders, neck or other parts of your body. If you experience any discomfort, put the device down and take a break. If you’re still experiencing discomfort after your break, consider calling a doctor.
Vibration function
The device has motors that may cause it to vibrate during gameplay or other use. For example, the device will vibrate briefly when turned on and off, and certain games may cause the device to vibrate. Extensive vibration may aggravate an injury to bones, joints or muscles of your hands or arms. If you have such an injury, you should disable vibration during gameplay or avoid games that make extensive use of the vibration function.
Seizures
A small percentage of people may experience seizures or blackouts that are triggered by visual stimuli, such as light flashes or patterns. These seizures occur most often in children or younger people and can be experienced by people who have never had seizures or blackouts before . Stop using Stadia or your Stadia Controller immediately if you suffer from blackouts or seizures and contact a doctor. If you have a history of seizures, blackouts or epilepsy, consult with a doctor before using Stadia or your Stadia Controller.
Proper Handling and Usage
Follow these guidelines when using, storing, cleaning or disposing of your Stadia Controller:
Care & cleaning
Unplug your Stadia Controller and adaptor before cleaning, during lightning storms or when unused for extended periods of time. Use a clean, soft and dry cloth to clean the device and accessories.
Do not use any chemical detergent, powder or other chemical agents (such as alcohol or benzene) to clean the Stadia Controller or accessories. Do not clean your device while it is charging.
Water resistance
You Stadia Controller, power adaptor and other accessories are not water resistant. Do not allow your device to come into contact with liquids. If your device is submerged in liquids, do not turn it on as it may cause electrical shorts and overheating. If it gets wet, do not attempt to dry it using an external heat source.
Magnetic fields
Avoid placing any media containing magnets or sensitive to magnetism, such as credit cards, bank cards, audio/video, tapes or magnetic memory devices, near your Stadia Controller or its charging cable, because you may lose information stored on those media. Media containing information sensitive to magnets should be kept at least 5 cms (2 inches) away from the Stadia Controller.
Connectors and ports
Ensure that the USB-C connector of your Stadia Controller is kept clean. Dirt in this connector may obstruct electrical current flow or cause overheating. You may clean the connector by first removing any dirt with a clean, soft and dry cloth. You may then blow compressed air from a can to further clean the connector. Hold the can upright to prevent liquid air from getting into the connector and at an angle to prevent dust and particles from getting further embedded in to the connector.
Do not insert any objects in the microphone opening at the back of the Stadia Controller. Doing so can damage your microphone.
Regulatory Information
Regulatory information, certification and compliance marks specific to Stadia Controller can be found on your device.
Regulatory Information: United States
FCC Regulatory Compliance
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, try to correct the interference in one or more of the following ways:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into a socket on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Google could void your authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- These devices may not cause harmful interference.
- These devices must accept any interference received, including interference that may cause undesired operation.
EMC Compliance Statement
Important: This device, charging cradle and power adaptor have demonstrated Electromagnetic Compatibility (EMC) compliance under conditions that included the use of compliant peripheral devices and shielded cables between system components. It is important that you use compliant peripheral devices and shielded cables between system components to reduce the possibility of causing interference to radios, televisions and other electronic devices.
Radio Frequency Exposure
This device has been evaluated and meets the applicable regulatory requirements for exposure to radio waves and is designed and manufactured not to exceed the applicable emission limits for exposure to radio frequency (RF) energy. To comply with RF exposure compliance requirements, this device must not be co-located or operating in conjunction with any other antenna or transmitter.
The Specific Absorption Rate (SAR) limit is 4.0 W/kg averaged over 10 gram of tissue for use in the hands. Stadia Controller complies with radio frequency specifications when used as a handheld device.
Stadia Controller maximum SAR value is:
1.14 W/kg when holding it in your hands
Recycling
For information about recycling in the United States, visit g.co/HWRecyclingProgram.
Regulatory Information: Canada
Innovation, Science and Economic Development Canada, Class B
This Class B digital apparatus complies with Canadian ICES-003.CAN ICES-3(B)/NMB-3(B).
Notice: The Innovation, Science and Economic Development Canada regulations provide that changes or modifications not expressly approved by Google could void your authority to operate this equipment.
Innovation, Science and Economic Development Canada (IC) Notices
Stadia Controller comply with Innovation, Science and Economic Development Canada (ISED or IC) licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) these devices may not cause interference, and (2) these devices must accept any interference, including interference that may cause undesired operation of the device.
Under Innovation, Science and Economic Development Canada regulations, the radio transmitter(s) in this device may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users, the antenna type and its gain should be chosen so that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Warning: The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Radio Frequency Exposure
This device has been evaluated and meets the applicable regulatory requirements for exposure to radio waves and is designed and manufactured not to exceed the applicable emission limits for exposure to radio frequency (RF) energy. To comply with RF exposure compliance requirements, this device must not be co-located or operating in conjunction with any other antenna or transmitter.
The Specific Absorption Rate (SAR) limit is 4.0 W/kg averaged over 10 gram of tissue for use in the hands. Stadia Controller complies with radio frequency specifications when used as a handheld device.
Stadia Controller maximum SAR value is:
1.14 W/kg when used as a normal handheld device with no separation
This device has been certified for use in Canada. Status of the listing in the Industry Canada’s REL (Radio Equipment List) can be found at the following web address: https://sms-sgs.ic.gc.ca/equipmentSearch/searchRadioEquipments?execution=e1s1&lang=en_CA
Additional Canadian information on RF exposure also can be found at the following web address: http://ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html
Informations réglementaires:
Innovation, Sciences et Développement économique Canada, Classe B
Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003.CAN ICES-3 (B)/NMB-3 (B).
Avis: Les réglementations d'Innovation, Sciences et Développement économique Canada prévoient que des modifications non expressément approuvées par Google pourraient annuler votre droit d'utiliser cet équipement.
Avis relatifs Innovation, Sciences et Développement économique Canada
Contrôleur Stadia respecter les normes RSS exemptes de licence d'Innovation, Sciences et Développement économique Canada (ISDE ou IC). Son utilisation est soumise aux deux conditions suivantes: (1) ces appareils ne doivent pas causer d’interférences, et (2) ces appareils doivent accepter toute interférence, y compris les interférences pouvant entraîner un fonctionnement non souhaité du dispositif.
En vertu des réglementations d'Innovation, Sciences et Développement économique Canada, les émetteurs radio de cet appareil ne peuvent fonctionner qu'avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Innovation, Sciences et Développement économique Canada. Pour réduire le risque de brouillage radioélectrique causé aux autres utilisateurs, le type d’antenne et son gain doivent être choisis de manière à ce que la puissance rayonnée de manière isotrope équivalente (par exemple) ne soit pas supérieure à celle nécessaire au succès de la communication.
Attention:
L'appareil destiné à fonctionner dans la bande 5150–5250 MHz est destiné uniquement à une utilisation en intérieur, afin de réduire les risques de brouillage préjudiciable causé aux systèmes de télécommunication par satellite mobiles dans le même canal.
Informations sur le débit d'absorption spécifique (DAS)
Cet appareil a été évalué et répond aux exigences réglementaires applicables en matière d’exposition aux ondes radio. Il est conçu et fabriqué pour ne pas dépasser les limites d’émission applicables en matière d’exposition à l’énergie de radiofréquence (RF). Pour être conforme aux exigences de conformité en matière d'exposition aux radiofréquences, cet appareil ne doit pas être co-implanté ou fonctionner conjointement avec une autre antenne ou un autre émetteur.
La limite de débit d'absorption spécifique (DAS) est de 4,0 W / kg en moyenne sur 10 grammes de tissu pour utilisation dans les mains. Le Stadia Controller est conforme aux spécifications de radiofréquence lorsqu'il est utilisé en tant qu'appareil de poche.
La valeur SAR maximale du contrôleur Stadia est la suivante:
1,14 W / kg lorsqu'il est utilisé comme un appareil de poche normal sans séparation
Cet appareil a été certifié pour une utilisation au Canada. L’état de la liste dans la liste REL d’Industrie Canada peut être consulté à l’adresse Internet suivante: https://sms-sgs.ic.gc.ca/equipmentSearch/searchRadioEquipments?execution=e1s1&lang=fr_CA
Des informations canadiennes supplémentaires sur l'exposition aux RF peuvent également être trouvées à l'adresse Web suivante: http://ic.gc.ca/eic/site/smt-gst.nsf/fra/sf08792.html
Regulatory Information: EU
EU Compliance Notice
Hereby, Google LLC declares that radio equipment type H2B is in compliance with Directive 2014/53/EU (Radio Equipment Directive). The full declaration of conformity may be found at g.co/home/red.
Restrictions and Requirements under Directive 2014/53/EU
The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range in AT, BE, BG, CY, CZ, DE, DK, EE, EL, ES, FI, FR, HR, HU, IE, IT, LT, LU, LV, MT, NL, PL, PT, RO, SE, SI, SK, UK, CH, IS, LI, NO, TR
The devices operate in the following frequency bands within the EU:
2400–2483.5MHz: Wi-Fi (max. 19 dBm), BLE (max. 9.8 dBm), 5150–5250 MHz: WLAN (max. 22 dBm), 5250–5350 MHz: WLAN (max. 22 dBm), 5470–5725 MHz: WLAN (max. 22 dBm).
Radio frequency interference
Google is not responsible for any radio or television interference caused by unauthorised modification of these devices or accessories or by the substitution or attachment of connecting cables and equipment other than that specified by Google. The correction of interference caused by such unauthorised modification, substitution or attachment is the responsibility of the user. Google and its authorised resellers or distributors are not liable for any damage or violation of government regulations that may arise from the user failing to comply with these guidelines.
The Specific Absorption Rate (SAR) limit is 4.0 W/kg averaged over 10 gram of tissue for use in the hands. Stadia Controller complies with radio frequency specifications when used as a handheld device.
Stadia Controller maximum SAR value is:
1.05 W/kg when used as a normal handheld device with no separation
Waste Electrical and Electronic Equipment (WEEE) Directive and Battery Directive
The WEEE symbol above means that according to local laws and regulations your product and its battery(ies) should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities for safe disposal or recycling. The separate collection and recycling of your product, its electrical accessories and its battery(ies) will help conserve natural resources, protect human health and help the environment.
Additional regulatory information: Germany
§ 10 I 2 ElektroG: Vor der Entsorgung dieses Geräts (i) Altbatterien/-akkus, sofern sie nicht vom Gerät umschlossen sind, und zerstörungsfrei entnehmbare Lampen zerstörungsfrei trennen und (ii) alle personenbezogenen Daten löschen. § 17 I und II ElektroG: Viele Vertreiber müssen Altgeräte kostenlos zurücknehmen.
RoHS Compliance
This product is in compliance with Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011, on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) and its amendments.
REACH
REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals, EC No. 1907/2006) is the EU chemical substances regulatory framework. Google complies with all requirements of the regulation and we are committed to providing our customers with information about the presence of REACH Substances of Very High Concern (SVHCs). For information, you can contact Google at [email protected].
The point of contact for regulatory matters in the EU is Google Commerce Limited, 70 Sir John Rogerson's Quay, Dublin 2, Ireland.
Manufacturer Info.
Manufacturer: Google LLC 1600 Amphitheatre Parkway Mountain View, CA, USA 94043
Importer Info.
Importer: Google Commerce Limited, 70 Sir John Rogerson’s Quay, Dublin 2, Ireland
Regulatory Information: Australia
WLAN function of these devices is restricted only to indoor use when operating in the 5150–5350 MHz frequency range to reduce the potential for harmful interference to co-channel mobile satellite systems.
Regulatory Information: Japan
Warning: 5 GHz bands (W52, W53) for indoor use only and cannot communicate to high power outdoor radio
Radio Frequency Exposure
This device has been evaluated and meets the applicable regulatory requirements for exposure to radio waves and is designed and manufactured not to exceed the applicable emission limits for exposure to radio frequency (RF) energy. To comply with RF exposure compliance requirements, this device must not be co-located or operating in conjunction with any other antenna or transmitter.
The Specific Absorption Rate (SAR) limit is 4.0 W/kg averaged over 10 gram of tissue for use in the hands. Stadia Controller complies with radio frequency specifications when used as a handheld device.
Stadia Controller maximum SAR value is:
1.05 W/kg when holding it in your hands
Limited Warranty
The limited warranty is available in the Google Hardware Warranty Centre.
©Google LLC. Google, Stadia and related marks and logos are trademarks of Google LLC
Bluetooth® is a registered trademark owned by Bluetooth SIG, Inc.
USB-C™ is a trademark of USB Implementers Forum.